audi engine tool FIND audi engine tool oil filter wrench -- mmk4mkt

Cam Bar and Pin for 2 Valve 139.50

Camshaft TimingTool Set (2)
TOOL REF 3243
Cam/Bar Holder 2 valves per cylinder/
Used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during belt change head assembly work.
Applicable Audi 90 A6 A4  94 97 AFC Engine

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF
BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6

Please note: 3243 for 2 valves per cylinder. 

Bar and Pin for 5 Valve 139.50

Camshaft Timing Tool Set (2)
TOOL REF 3391
Cam/Bar Holder
V6 / 5 valves per cylinder/
used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during timing belt change /head assembly work.
Applicable VW Audi V6 5 Valve 1998 2003
Cam/Bar Holder Not Applicable 3.0 2002 4 cam.

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6Please note: 3391 for 5 valves per cylinder.

Audi Headbolt Tool 17.50

This is the tool you are looking for!
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

Spark Plug Boot Tool 32.99
Spark Plug Boot Tool
Due to restricted space the T10029 will install the spark plug boot properly.
VW and Audi spark plug boots designed to seal and increase contact between the spark plug and spark plug wire.
With the increased seal and location of the boot,
this tool has been made to access and remove the spark plug boot.
Tool is approximately 10 inches (250mm) long.
Used to pull off the spark plug socket...SOME APPLICATIONS INCLUDE: 2.8 2.9L VR6 engines
VW Golf, Corrado and Passat.Also Audi 80, 100, A4, A6 with 2.6 and 2.8L V6 engines.
This is the correct tool for the job.You will most likely find OLD number 3277 or 3277A in your manuals but
T10029 is the CORRECT current Volkswagen Audi Tool number. 3277 is and old number and Volkswagen calls this a SPARK PLUG CONNECTOR TOOL.
read more:

22mm Lambda Tool 96.99

4681 1 Open Box Wrench 22mm chrome plated,
10 offset, with square connection 9 x 12 mm
for using with HAZET 6396,
For Lambda probe on VW AUDI, engine BMW M 70,
750i, 320, 325 M 20 engine, 316, 318 M 43 engine,
FORD Fiesta 1.1 and 1.6 l, Escort Orion 1.4 l

Tappett Depressor 44.99

Tappet Depressor needed for preloading cam followerswhile exchanging valve adjusting shims.Applicable: Late model VW Audi 4 and 5 cylinder gas engines.More Detail: Some German Tool books have the following info on this tool...For all 4 cylinder engines with bucket tappets 1983 and Newerand all 5 and 6 Cylinder with bucket tappetsGolf, Jetta, Scirocco, Passat, Audi 80, Audi 80 Coupe,Audi 80 Quatro, Audi 100, 200,LT28 50D

Audi Headbolt Toolt 17.50

Tappet Depressor 44.99

Tappet Depressor 2078A used for preloading cam followerswhile exchanging valve adjusting shims.Applicable: Late model VW Audi 4 and 5 cylinder gas engines.More Detail: Some German Tool books have the following info on this tool...For all 4 cylinder engines with bucket tappets FROM YEAR 1983 and Newerand all 5 and 6 Cylinder with bucket tappetsGolf, Jetta, Scirocco, Passat, Audi 80, Audi 80 Coupe,Audi 80 Quatro, Audi 100, 200, LT28 50D

Pin Wrench Set 2 49.00

This is the Best Quality Set of the two CRUCIAL VW Audi Pin Wrenches you will find anywhere.
SUPER HIGH QUALITY TOOLS (BOTH) MADE IN GERMANY BY HAZET.
First item is number V159 (this is a smaller tool on the left side picture is not to scale) This tool is for easy adjustment of Camshaft spur belts
(toothed belt) on idler pulleys with Pin holes. This wrench with its protruding pins, grabs the center
of the idler pulley and rotates around the off center retaining bolt allowing for easy belt tension adjustment.
Tension Pulleys on 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80
Distance of pins 18 mm, diameter of pins 2.9 mm for deep located idler pulley
on toothed belt on 1,6 l diesel engine VW van T3 (up to model 1991).
V159 is the correct number the old VW Number on this (smaller) tool was 2587.

T10020 Special wrench with an offset (angled) head (Larger tool on right side of image)
This tool also used for adjusting timing belt tension.
99 and later VW Golf, VW Jetta and Beetle with 2.0 Litre Gas and 1.9 Litre TDI Engines.1999 and newer Golf, Jetta
New Beetle with 2.0l gas engine and 1.9l T.D.I. Diesel engine. You will get both tools with this purchase.

Headbolt & Drain Plug Socket Set 2 28.00

Drain Plug Socket
Plus Heabolt Tool
Details: Tamperproof Transmission Drain Plug Socket.
Triple Square (12 Point XZN)
Same as Volkswagen Tool 3357.
For Porsche Boxster and Audi A4, A6 and Passat.

Plus Audi Headbolt Tool
Number T10070 Headbolt Tool 1/2 Drive Used to remove and install cylinder headbolts. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2 inch. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. Set of 2 Audi Tools from ZDMAK

Dont hesitate...these are BOTH the CORRECT tools for the job!

Pin Wrench Socket 14.99

VW524Pin Wrench Socket with 1/2" drive.This tool is used for R&R of grooved ring retaining nuton strut tower of front shock absorber. Applicable: This popular tool is used on a wide variety of VW and Audi MK1 golf and GTi , MK2 Golf & GTi 8V and 16VPolos..Audi Coupe..Audi 80 & Audi 90
Also used for adjusting power steering gear on VW Jetta, Golf, GTI.

2 Pins and 2 Plates 103.00

2 Pins and 2 Plates Set of four tools.VW Audi T.D.I. and New Beetle Cam Kit Reference numbers for the two tools on the left are: 3418 and 3359. Tool Set for factory correct and trouble free installations. This is a popular set for Diesel timing of Bosch injection pumps. This set has been developed for aligning the cam shaft with the Diesel pump on 1998 and newer VW models equipped with a T.D.I. engine. This two piece lock plate and alignment pin allows the technician for factory correct and trouble free installations.

Tools on the right side of image are Diesel Lock Plate / Cam Setting Bar Same as Volkswagen ref 2065a Tool used for securing the cam shaft from rotating and maintaining correct timing position engine AAZ during R&R of cam shaft drive belt. Applicable: VW/Audi diesel and Volvo 6 cylinder 2.4L diesel 1981 86 Lock Pin for Diesel (Same as VW tool 2064). Tool used for securing Bosch diesel injection pump sprocket from rotating during R&R of cam shaft drive belt. This Locking Pin also assists in locating the general timing position of pump. Volkswagen Audi diesel and Volvo 6 cylinder 2.4L diesel 1981 86 All 4 tools are High Quality Made in Europe!

Audi VW Headbolt Tool Set 2 29.50

These are the tools you are looking for!VW AUDI Headbolt Tools 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi
Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tools. Please read: The T10070 is the correct current VW Audi number for this new style tool.The old tool number was 3452 and is now discontinued.Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this new style a Polydrive.

Plus you get Headbolt Tool Triple Square 12 Point (XZN) Socket M10Sturdy 1/2 Drive Tools used for a wide variety of applications including headbolts.Excellent for working on German vehicles.
This XZN tool is 5 1/2 inches long and the shaft is 4 inches.
Super set for removing & installing cylinder headbolts on both early and late model 1.8T and 2.0L gas engines. You will get both tools with this purchase.

End Play Kit 00
This tool has isdesigned to measure the end play movement
of the VW crankshaft without the use of a dial indicator.
All that is necessary is a feeler gauge set and this tool.
With the tool bolted to the end of the case, the feeler guage
measures the gap created by the end play.
The taking of this end measurement is necessary whenever a VW engine is rebuilt
to prevent the rear main bearing from seizing up.
A must for rebuilding one engine or many,
this tool works on all air cooled VW engines and Porsche 912 & 914 models.
read more:

Headbolt Socket 17.50

This is the tool you are looking for.
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

Top Dead Center Indicator 14.50
Top Dead Center Indicator9710 Used for T.D.C. on any Gas engine.Simply unscrew a spark plug and twist the rubber hosepart of this tool into the spark plug hole.As you rotate the engine with a turning bar,the piston forces air through the whistle part of this tool.Once the whistling stops the engine is at T.D.C.
read more:

Valve Spring Tool & Bridge 142.50

Valve Tools (2)
Set including:Valve Spring Compressor Bar
Same as Volkswagen Tool Number VW 541/1
Used for R&R of valve spring or rocker armWith this tool the job can be done with the cylinder head on or off the car.Used in conjunction with tool BridgeApplicable: 924 / 944 VW AUDI 4 5 Cyl. VA6022Support Bridge Same as VW Tool 2036 Used for R&R of valve spring or rocker armUsed in conjunction with tool VW541/1Applicable: Model 924. VW / AUDI 4 5 Cyl.

Super Duty Headbolt Tool 37.50

Headbolt Tool ....Read:
Same as Number T10070
Super Strong Headbolt Tool 1/2 Drive
(notice the solid one piece design)
Tool used to remove and install cylinder headbolts. New "Stronger" One Piece design. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2" Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socket The old tool number was 3452 and is now discontinued.. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. The German Tool Books call this a Polydrive. This is NOT a Torx socket although it is a 6 point tool. The points are more flat (squared off) than a torx. and it is NOT a XZN (tri square) Socket.

Tappet Depressor Set 81.50

VW546 Tappet Depressor Tappet Depressor used for preloading cam followers. For Bucket Tappets on VW Golf, Jetta, Caddy, Scirocco, Passat up to 1982 Also Audi 80 , 100

Plus 2078A Tappet Depressor needed for preloading cam followers while exchanging valve adjusting shims. Applicable: Late model VW Audi 4 and 5 cylinder gas engines. More Detail: Some German Tool books have the following info on this tool... For all 4 cylinder engines with bucket tappets 1983 and Newer and all 5 and 6 Cylinder with bucket tappets Golf, Jetta, Scirocco, Passat, Audi 80, Audi 80 Coupe, Audi 80 Quatro, Audi 100, 200, LT28 50D.

Valve Spring Tool and Bridge 142.50

Valve Spring Tools Set including:VA6010Valve Spring Compressor BarSame as Volkswagen Tool Number VW 541/1Used for R&R of valve spring or rocker armWith this tool the job can be done with the cylinder head on or off the car.Used in conjunction with tool BridgeApplicable: 924 / 944 VW AUDI 4 5 Cyl. VA6022Support Bridge Same as VW Tool 2036 Used for R&R of valve spring or rocker armUsed in conjunction with tool VW541/1Applicable: Model 924. VW / AUDI 4 5 Cyl.

Spark Plug Boot Tool 24.99

Spark Plug Boot Tool
Due to restricted space the T10029 will install the spark plug boot properly.
VW and Audi spark plug boots designed to seal and increase contact between the spark plug and spark plug wire.
With the increased seal and location of the boot,
this tool has been made to access and remove the spark plug boot.
Tool is approximately 10 inches (250mm) long.
Used to pull off the spark plug socket on 2.8 2.9L VR6 engines
VW Golf, Corrado and Passat.Also Audi 80, 100, A4, A6 with 2.6 and 2.8L V6 engines.
This is the correct tool for the job.You will most likely find OLD number 3277 or 3277A in your manuals but
T10029 is the CORRECT current Volkswagen Audi Tool number. 3277 is and old number and Volkswagen calls this a SPARK PLUG CONNECTOR TOOL.

Holder Plate Only from Cam Kit 00

Plate appl:700, 800, 850, 900, 960, C70 Conv, C70 Coupe, S40, S70, S90, V40, V70 2000, V70 XC, V90
Engine:B4164S Engine:B4164S2, Engine:B4184S, Engine:B4184S2, Engine:B4184S3, Engine:B4194T, Engine:B4204S, Engine:B4204S2, Engine:B4204T, Engine:B5202FS, Engine:B5204FS, Engine:B5204FT, Engine:B5204T2, Engine:B5204T3, Engine:B5204T4, Engine:B5234FS,

Headbolt & Drain Plug Socket Set 28.00

TWO TOOLS!!!
Audi Headbolt Tool (LEFT)Number T10070 Headbolt Tool 1/2 Drive Used to remove and install cylinder headbolts. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2 inch. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. Plus Drain Plug Socket (right)Special Tamperproof Transmission Drain Plug Socket.Triple Square (12 Point XZN)Same as Volkswagen Tool 3357.For Porsche Boxster and Audi A4, A6 and Passat. Dont hesitate...these are BOTH the CORRECT tools for the job!

Cam Adjustment Pieces Only * from Cam Kit 00

CAMSHAFT ADJUSTMENT TOOL
Same as Volvo 5452
700, 800, 850, 900, 960, C70 Conv, C70 Coupe, S40, S60, S70, S80, S90, V40, V70 2000, V70
Engine:B4164S Engine:B4164S2, Engine:B4184S, Engine:B4184S10, Engine:B4184S2, Engine:B4184

Power Steering Waterpump Pulley Tool 24.00

VA6024Power Steering and Waterpump Pulley Removal & Replacement Tool Volkswagen AudiUsed to hold the power steering or water pump pulley stationarywhile removing or replacing the three socket headbolts that attach pulley to the shaft.Tool is designed to be used on pulleys that utilize these socket head bolts.Applications:VW Audi 4 cylinder water cooled gas or diesel engines from 1975 to current.Volkswagen V6 1992 and newer.Audi power steering pump pulley V8 1990 and newer.Audi V6 1992 to current.Also VW 1983 to 1988 and Audi 1981 to 1995 with socket head boltsholding the pulley to power steering pump.

Headbolt Tool Set 2 29.50

These are the tools you are looking for!
Plus they are on sale!
Headbolt Tools 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen Audi
Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tools. Please read: The T10070 is the correct current VW Audi number for this new style tool.The old tool number was 3452 and is now discontinued.Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this new style a Polydrive.

Plus you get Headbolt Tool Triple Square 12 Point (XZN) Socket M10Sturdy 1/2 Drive Tools used for a wide variety of applications including headbolts.Excellent for working on German vehicles.
This XZN tool is 5 1/2 inches long and the shaft is 4 inches.
Super set for removing & installing cylinder headbolts on both early and late model 1.8T and 2.0L gas engines. You will get both tools with this purchase.

PULLEY HOLDING TOOL 74.99

AUDI & VW
FAN CLUTCH PULLEY HOLDING TOOL
AUDI 1996 2001 A6 2.8L V 6 & VW 1998 & later Passat 3.0L V 6

Pin Wrench 37.00

Heavy Duty Tensioner with Handle Grip
Same as Volkswagen number T10020
VW AUDI TENSION PULLEY SPANNER WRENCH This unique tool is for 1998 and later VW and Audi which require spanner wrench adjustments to the timing belt.Details: Special Wrench for adjusting the belt tension on the following: Audi: A6 1.6 (96 and newer) ALZ VW: Polo Classic, Golf, Bora, New Beetle 1.6 (97 ) AEH / AKL / APF / AUR /AVU / AYD Golf, Bora, New Beetle, 2.0 (98 ) AQY / APK

This is the new style Pin wrench with the (offset) angled head, same as the factory tool only this tool is a little longer for leverage with a rubber handle grip for a better feel compared to the smaller version.

Cam Bar for 2 Valve 129.50

Camshaft Securing Bar Timing Tool
TOOL REF 3243
Cam/Bar Holder 2 valves per cylinder/
Used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during belt change head assembly work.
Applicable Audi 90 A6 A4 94 97 AFC Engine
Please note: 3243 Securing Bar for2 valves per cylinder.

Super Duty Pin Wrench 37.00

Press Set 2 Only * from Cam Kit 00

Press tools (pair) appl: 700, 800, 850, 900, 960, C70 Conv, C70 Coupe, S40, S60, S70, S80, S90, V40, V70 2000, V70 2000 , V70 XC, V70 XC 2001 , V70 XC 2001 / XC70, V90, XC90,
Engine:B4164SEngine:B4164S2, Engine:B4184S, Engine:B4184S10, Engine:B4184S2, Engine:B4184S3, Engine:B4184S9, Engine:B4194T, Engine:B4194T2, Engine:B4204S, Engine:B4204S2, Engine:B4204T, Engine:B4204T2, Engine:B4204T2 CVVT, Engine:B4204T3, Engine:B4204T3

New Style Headbolt Polydrive 17.50

This is the tool you are looking for!
Plus it is on sale!
Number T10070 Headbolt Tool 1/2 Drive
Used to remove and install cylinder headbolts.
Volkswagen AudiV6 and 4 Cylinder5 valve engines. Long pattern for deep located screws. Drive size is 1/2"Dont be stuck using the wrong tool for this application. T10070 is the correct current VW Audi number for this socketThe old tool number was 3452 and is now discontinued..Many Audi Headbolts have switched to the new pattern.This will fit into the new special screw profile.The German Tool Books call this a Polydrive.This is NOT a Torx socket although it is a 6 point tool.The points are more flat (squared off) than a torx.and it is NOT a XZN (tri square) Socket.

Cooling System Adapter 15.50

VOLKSWAGEN AUDI
COOLING SYSTEM ADAPTER
APPLICABLE:
VW AUDI WITH MALE THREADSON FILLER NECK OF EXPANSION TANK
(VW ALL PRE 90 / AUDI ALL PRE 90)
THIS IS A QUALITY TOOL MADE IN EUROPE

Special Hook 3370 29.99
Factory Tool 3370
Made in Germany.
TOOL USED TO REMOVE FRONT SEAT BACK REST PANEL ON AUDI A4.
read more:

Complete VW Audi Radio Keys 24.99

Set of Volkswagen Audi Radio Removal Tools Audi A4, A6, A8 and New Beetle For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box.
PLUS * Set Number vw 3316 Radio Removal Tools New Body Style Passat Jetta Golf Please check your manuals for details.
You will get virtually full VOLKSWAGEN coverage with this set
Plus BMW Radio Removal Tool.Pentagon shaped tool with 3 5/8 inches overall length.Applicable: Most BMWs.This Five sided driver is used to release anti theft radio mounts.YOU ALSO GET THE SPECIAL SMALL ALLEN (Right) side of picture FOR NEWER E38 & E39 7 SERIES
Plus * MERCEDES RADIO REMOVAL KEYS FOR NEWER AND OLDER VEHICLES

Volkswagen Door Tool 9.99

T10011Volkswagen Door Tool triple Square 4
This is the correct tool for the job
New Beetle Tool This tool is used for R & R of door handle screws.Applicable: 1998 & newer VW Golf, Jetta, Passat & New Beetle....possibly other VW Audi.
This tool is a high quality item you will like.

10mm Glow Plug Tool 69.99

10mm Universal Glow Plug Socket mainly for VW Audi Diesel Injection TDI 3/8 Drive.
High quality tool
Made in Germany by Hazet!
DETAILS: ALFA ROMEO, AUDI, CHRYSLER, FIAT, FORD, MERCEDES, LAND ROVER, RENAULT, SEAT, VOLKSWAGEN.

End Play Kit 16.95

This tool has isdesigned to measure the end play movement
of the VW crankshaft without the use of a dial indicator.
All that is necessary is a feeler gauge set and this tool.
With the tool bolted to the end of the case, the feeler guage
measures the gap created by the end play.
The taking of this end measurement is necessary whenever a VW engine is rebuilt
to prevent the rear main bearing from seizing up.
A must for rebuilding one engine or many,
this tool works on all air cooled VW engines and Porsche 912 & 914 models.

Top Dead Center Indicator 14.99

Top Dead Center Indicator9710 Used for T.D.C. on any Gas engine.Simply unscrew a spark plug and twist the rubber hosepart of this tool into the spark plug hole.As you rotate the engine with a turning bar,the piston forces air through the whistle part of this tool.Once the whistling stops the engine is at T.D.C.

Timing Kit Master Set 1 254.00

Serious Master Set: Description (for upper 3 tools) Timing belt on engine ALH. Chassis 1999 1/2 thru 2003 Golf Jetta (A4) MKIV and New Beetle TDI thru 2003.Reference numbers for the three tools are 3418 (Left side of image above) 3359 (Pin Center) and T10020 (Wrench Right. This is a popular set for Diesel timing of Bosch injection pumps. This set has been developed for aligning the cam shaft with the Diesel pumpon 1998 and newer VW models equipped with a T.D.I. engine.

BELOW IS THE DESCRIPTION ON THE LOWER 5 TOOLS. Five tools: vw 3032, 2066, 2065A, 2064 and 12717 (Pin Wrench) Details: 3032 Injection Pump Tool Puller used for the proper extraction of injection pump drive gear. Applicable: VW / Audi diesels : 2066 Used for accurate adjustment of Bosch diesel injection pump. 2065A Diesel Camshaft Locking Plate Tool 2064 Lock Pin for Diesel. Pin Wrench 121717 Made in Germany for easy adjustment of Camshaft spur belts (toothed belt) on idler Pulleys with Pin holes. This wrench with its protruding pins, grabs the center of idler pulley and rotates around the off center retaining bolt allowing for belt tension adjustment (Tension Pulleys) 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80. You will get all 8 tools shown here.

17 x 17 Injection Wrench 39.50
Double Ended Flare Nut Box Wrench Size 17 x 17mmOverall Length 241mm (9.5 inch)For injection pipes on Volkswagen / Audi This tool will help you when you remove and install the fuel lines from the injection pump and the injectors themselves.For TDI: You will still need to torque the 17mm fittings down to spec, but this tool will make taking the fittings off a snap, as well as putting them back on.This is a Factory Tool Made in Germany
read more:

Cam Bar for 5 Valve 129.50

Camshaft Timing Tool Securing Bar
TOOL REF 3391
Cam Securing Bar Holder
V6 / 5 valves per cylinder/
used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during timing belt change /head assembly work.
Applicable VW Audi V6 5 Valve 1998 2003
Cam/Bar Holder Not Applicable 3.0 (2002 4 cam)
Please note: 3391 for 5 valves per cylinder.

FENDER PROTECTOR 0.00

FENDER PROTECTOR FOR AUDI
PREVENTS DAMAGE TO FRONT QUARTER PANELS ON AUDI VEHICLES DURING REPAIR. COVER WILL NOT SCRATCH VEHICLE. SUITABLE FOR ALL AUDI MODELS * EXCEPT AUDI TT

V8 Camshaft Securing Bar 135.00

V8 Timing Tool T40005
Camshaft Securing Bar Audi A6 / A8
Used for the crucial taskof securing both engine banks, cam shafts at T.D.Cwhen replacing the timing belt.

Radio Removal Set 24.99

Best Seller ! Radio Tools Set 24.99

This is one of the best sets on the market. This is a Master Set for BMW Mercedes Porsche VW Audi and DIN. Included is a total of 3 different sets Volkswagen Audi, two different tools for BMWand a set for Mercedes Porsche and a DIN Ford set. The VW Tools (4) Number T10057Audi A4, A6, A8 and New Beetle For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box. If you have 4 slots VW AUDI this is the 4 keys you need) Plus you get Number VW 3316 (2) Radio Removal Tools New Body Style Passat Jetta Golf . You will get virtually full coverage forVolkswagen Audi when you buy this master set. The BMW Radio Removal Tools areone Pentagon shaped tool with a 3 5/8 inches overall length. Applicable: Most BMWs. This Five sided driver is used to release anti theft radio mounts.You will also get the special rare small allen tool for BMW (upper left) Fornewer BMW E38 & E39 7 SERIES Plus Mercedes most coverage for newer and oldervehicles, especially 1992 and newer 129, 140, 163, 202 & 210 PLUS Range Rover with Becker Nav System.The MB Tools also work on Porsche. Appl: Turbo GT, GT2, GT3, Boxster, Cayenne 911, 996 , 987, Carrera etc. Same as Porsche ref: 000 721 957 01

Threaded Pin for T.D.C. 25.00

Locking Pin
TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF
BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6
For installing or removing toothed belt /flywheel drive plate.

Hex Socket 27mm 14.99

Hex Socket 27mm with 3/8" Drive Special Tool 27mm hex Used for R&R of 27mm "female" hex timing plug of engine bell housing and R&R of 27mm female hex transmission access cover. Picture is not to scale. Applicable: All VW/Audi water cooled models '75 and newer.

World Class Hazet Tools 0.00

Number 2593 28 Shock absorber cartridge socket 295mm long. For Audi 80 from 1992 on and Audi 90 from 1987.
1/2 inch drive.
High Quality Tool Made in Germany.

Special Adaptor Ring * 154.50

New Porsche Adaptor Ring
For the budget minded Porsche & VW air cooled engine rebuilder...Check it out.....
This Ring (same as the one equipped on the factory style Engine Holding Fixture P201)
is void of any holding or securing tubes.
This adaptor ring is specifically designed to mate the engine case straight to any universal engine stand, using four 3/8" Bolts,
thus allowing for a full 360 degree rotation of the engine.
This ring is designed to bolt up to every Porsche and VW fully dressed air cooled engine ever produced.
It is machined with all the necessary reliefs and/or notches to allow for clearance of all engine parts, including the flywheel and its respective lock tool (VW Flywheel lock 215). Call Zdmak 877 938 6657.

You Searched for

audi engine tool

Trade Links With ZDMAK