bmw engine tool porsche engine tool audi engine tool oil filter wrench -- mmk4mkt

Top Dead Center Indicator 14.50
Top Dead Center Indicator9710 Used for T.D.C. on any Gas engine.Simply unscrew a spark plug and twist the rubber hosepart of this tool into the spark plug hole.As you rotate the engine with a turning bar,the piston forces air through the whistle part of this tool.Once the whistling stops the engine is at T.D.C.
read more:

Holder Plate Only from Cam Kit 00

Plate appl:700, 800, 850, 900, 960, C70 Conv, C70 Coupe, S40, S70, S90, V40, V70 2000, V70 XC, V90
Engine:B4164S Engine:B4164S2, Engine:B4184S, Engine:B4184S2, Engine:B4184S3, Engine:B4194T, Engine:B4204S, Engine:B4204S2, Engine:B4204T, Engine:B5202FS, Engine:B5204FS, Engine:B5204FT, Engine:B5204T2, Engine:B5204T3, Engine:B5204T4, Engine:B5234FS,

Cam Adjustment Pieces Only * from Cam Kit 00

CAMSHAFT ADJUSTMENT TOOL
Same as Volvo 5452
700, 800, 850, 900, 960, C70 Conv, C70 Coupe, S40, S60, S70, S80, S90, V40, V70 2000, V70
Engine:B4164S Engine:B4164S2, Engine:B4184S, Engine:B4184S10, Engine:B4184S2, Engine:B4184

Press Set 2 Only * from Cam Kit 00

Press tools (pair) appl: 700, 800, 850, 900, 960, C70 Conv, C70 Coupe, S40, S60, S70, S80, S90, V40, V70 2000, V70 2000 , V70 XC, V70 XC 2001 , V70 XC 2001 / XC70, V90, XC90,
Engine:B4164SEngine:B4164S2, Engine:B4184S, Engine:B4184S10, Engine:B4184S2, Engine:B4184S3, Engine:B4184S9, Engine:B4194T, Engine:B4194T2, Engine:B4204S, Engine:B4204S2, Engine:B4204T, Engine:B4204T2, Engine:B4204T2 CVVT, Engine:B4204T3, Engine:B4204T3

End Play Kit 16.95

This tool has isdesigned to measure the end play movement
of the VW crankshaft without the use of a dial indicator.
All that is necessary is a feeler gauge set and this tool.
With the tool bolted to the end of the case, the feeler guage
measures the gap created by the end play.
The taking of this end measurement is necessary whenever a VW engine is rebuilt
to prevent the rear main bearing from seizing up.
A must for rebuilding one engine or many,
this tool works on all air cooled VW engines and Porsche 912 & 914 models.

Top Dead Center Indicator 14.99

Top Dead Center Indicator9710 Used for T.D.C. on any Gas engine.Simply unscrew a spark plug and twist the rubber hosepart of this tool into the spark plug hole.As you rotate the engine with a turning bar,the piston forces air through the whistle part of this tool.Once the whistling stops the engine is at T.D.C.

Special Adaptor Ring * 154.50

New Porsche Adaptor Ring
For the budget minded Porsche & VW air cooled engine rebuilder...Check it out.....
This Ring (same as the one equipped on the factory style Engine Holding Fixture P201)
is void of any holding or securing tubes.
This adaptor ring is specifically designed to mate the engine case straight to any universal engine stand, using four 3/8" Bolts,
thus allowing for a full 360 degree rotation of the engine.
This ring is designed to bolt up to every Porsche and VW fully dressed air cooled engine ever produced.
It is machined with all the necessary reliefs and/or notches to allow for clearance of all engine parts, including the flywheel and its respective lock tool (VW Flywheel lock 215). Call Zdmak 877 938 6657.

Pin Only from Cam & Crank Kit 00

Pin Only Appl: 700, 800, 850, 900, 960, C70 Conv, C70 Coupe, S40, S60, S70, S80, S90, V40, V70 2000, V70
Engine:B4164S Engine:B4164S2, Engine:B4184S, Engine:B4184S10, Engine:B4184S2, Engine:B4184

Professional Engine Holder Complete 550.00
Engine Holding Fixture Designed to securely carry the entire weightof a fully dressed air cooled twin turbo Boxer 6.Engine Holding Fixture will allow a full 360 degree rotation of engine,with Flywheel Lock allowing for R&R of engine.Bolts up to every Porsche and VW air cooled Boxer ever produced.From Type 1 up to 3.6LItems included in this kit are: P201, VW313 and VW215.
read more:

22mm Lambda Tool 96.99

4681 1 Open Box Wrench 22mm chrome plated,
10 offset, with square connection 9 x 12 mm
for using with HAZET 6396,
For Lambda probe on VW AUDI, engine BMW M 70,
750i, 320, 325 M 20 engine, 316, 318 M 43 engine,
FORD Fiesta 1.1 and 1.6 l, Escort Orion 1.4 l

Cam Bar and Pin for 2 Valve 139.50

Camshaft TimingTool Set (2)
TOOL REF 3243
Cam/Bar Holder 2 valves per cylinder/
Used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during belt change head assembly work.
Applicable Audi 90 A6 A4  94 97 AFC Engine

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF
BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6

Please note: 3243 for 2 valves per cylinder. 

Cam Bar and Pin for 2 Valve 139.50

Set 3 Valve Tools 105.50
VALVE ADJUSTING TOOL SET OF 3
Valve adjusting on the Rabbit, Scirocco, and Jetta 1 requires the use of a special tool to hold the cam followers in the down position in order to remove the shims for replacement. The valve adjusting pliers are then used to remove the shim. Note: The 1.6 and 1.7 liter engines use a different tool than the 1.8 liter engine becuase of valve spacing. The Shim Set works on all solid lifter cylinder heads.
read more:

Finger Tip Spark Plug Tool 00

Finger Tip Spark Plug Tool.
For deep seated plugs in tight engine compartments.

read more:

ENGINE SLING 0.00

2024A FACTORY TOOL USED TO REMOVE AND INSTALL ENGINE

Valve Tool for Volkswagen 61.95

Valve Tool for Volkswagen Valve Tool for VolkswagenThis unique tool has been designed to allow removal and installation of valve springs while the engine is still in the carType I, II III engines 40 HP and laterThis set will also remove springs on disassembled engines.

Special Rivet Tool 0.00
Special Rivet Tool
Plier with 90 degree rotating head.
Tool used to remove two piece reusable plastic rivets
found on door panels, engine shields, wheel well shields etc.
For undivided rivets the Plier can also be used for cutting the head off the rivet.
Easy to use universal Plier eliminates damage to trim and door facings.
read more:

Support Frame 85.00

Engine Bracket Original Factory Tool Made in Germany: USE FOR SUPPORTING W8 ENGINE

Pin Wrench Set 2 49.00

This is the Best Quality Set of the two CRUCIAL VW Audi Pin Wrenches you will find anywhere.
SUPER HIGH QUALITY TOOLS (BOTH) MADE IN GERMANY BY HAZET.
First item is number V159 (this is a smaller tool on the left side picture is not to scale) This tool is for easy adjustment of Camshaft spur belts
(toothed belt) on idler pulleys with Pin holes. This wrench with its protruding pins, grabs the center
of the idler pulley and rotates around the off center retaining bolt allowing for easy belt tension adjustment.
Tension Pulleys on 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80
Distance of pins 18 mm, diameter of pins 2.9 mm for deep located idler pulley
on toothed belt on 1,6 l diesel engine VW van T3 (up to model 1991).
V159 is the correct number the old VW Number on this (smaller) tool was 2587.

T10020 Special wrench with an offset (angled) head (Larger tool on right side of image)
This tool also used for adjusting timing belt tension.
99 and later VW Golf, VW Jetta and Beetle with 2.0 Litre Gas and 1.9 Litre TDI Engines.1999 and newer Golf, Jetta
New Beetle with 2.0l gas engine and 1.9l T.D.I. Diesel engine. You will get both tools with this purchase.

Transport Brackets 59.10

Engine Brackets Original Factory Tool Made in Germany: USED WHEN REMOVING AND INSTALLING W8 ENGINE ON PASSAT.

Neway Valve Seat Cutter 0.00
Neway Valve Seat Cutter
Neway has been in business since 1952 manufacturing and distributing tools and equipment for valve seat reconditioning and valve reconditioning.The "trademark" product is the Neway valve seat cutter. Neway seat cutters are almost standard equipment in any machine shop that services four stroke engines whether the work is small engine repair, automotive high performance, routine motorcycle maintenance, or heavy duty engine rebuilding. Neway offers value. It is extremely easy to use and accurate enough to be the tool of choice for high performance engine work, and it does not require a major investment.
For More info call or email.
read more:

Bar and Pin for 5 Valve 139.50

Camshaft Timing Tool Set (2)
TOOL REF 3391
Cam/Bar Holder
V6 / 5 valves per cylinder/
used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during timing belt change /head assembly work.
Applicable VW Audi V6 5 Valve 1998 2003
Cam/Bar Holder Not Applicable 3.0 2002 4 cam.

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6Please note: 3391 for 5 valves per cylinder.

Passat Seal Tool 19.50

T10249 Made in Germany
Used for sealing lines when removing additive reservoir.Passat 4 cyl. diesel engine (2.0 ltr. engine)

T10004 59.50

Original Factory Tool T10004 PIN WRENCH USAGE: Used for removing and installing and tensioning of toothed belt on Jetta 2.0 Liter SULEV engine with engine code BBW. Made in Germany.

VR6 ENGINE SUPPORT 0.00

ENGINE SUPPORT FOR VR6 ENGINE. USED WHEN ASSEMBLING/DISASSEMBLING ENGINE BLOCK

ADJUSTING TOOL 17.50

FACTORY TOOL USED FOR INSTALLATION AND BASIC SETTING OF THE IGNITION DISTRIBUTOR ON THE 20 VALVE ENGINE

ADJUSTING TOOL 24.95

FACTORY TOOL USED FOR INSTALLATION AND BASIC SETTING OF THE IGNITION DISTRIBUTOR ON THE 20 VALVE ENGINE

Cam Bar for 2 Valve 129.50

Camshaft Securing Bar Timing Tool
TOOL REF 3243
Cam/Bar Holder 2 valves per cylinder/
Used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during belt change head assembly work.
Applicable Audi 90 A6 A4 94 97 AFC Engine
Please note: 3243 Securing Bar for2 valves per cylinder.

Vanos Turning Tool 19.99

Sprocket Tool Ref: 90 88 6 115 490 For turning sprockets when removing and installing VANOS unit some applications include: BMW Engine M50, M52, M50 US, M52 US

Vanos Turning Tool 27.99

Sprocket Tool Ref: 90 88 6 115 490 For turning sprockets when removing and installing VANOS unit some applications include: BMW Engine M50, M52, M50 US, M52 US

Crankshaft Stop 59.50

Crankshaft Stop Original Factory Tool Made in Germany: 4 Cyl. diesel engine (1.9 l and 2.0 l engine, 2 and 4 valve. Fixing the crankshaft in place at the oval crankshaft pulley when adjusting the valve timing TDC marking at 1 oclock. (Use of the oval belt pulley will be gradually introduced).

The School of Automotive Machinists Accepted as Contestant in the JEG’s Engine Masters Challenge Presented by Popular Hot Rodding
The School of Automotive Machinists, SAM, is pleased to announce that it has been accepted as a contestant in the JEG’s Engine Masters Challenge presented by Popular Hot Rodding. The School’s engine will be competing with 48 other engines built by some of the most experienced engine builders in the nation. (PRWEB Jun 26, 2006)
read more:

Mercedes Special Tool 00

Special Tool for MERCEDES Star.
Chrome plated,with T handle made of black plastic,for mounting and removing theMercedes Star at the engine hood
on class S (W 140), E(W 124 since model 93) and C (W 202)

2 Pins and 2 Plates 103.00

2 Pins and 2 Plates Set of four tools.VW Audi T.D.I. and New Beetle Cam Kit Reference numbers for the two tools on the left are: 3418 and 3359. Tool Set for factory correct and trouble free installations. This is a popular set for Diesel timing of Bosch injection pumps. This set has been developed for aligning the cam shaft with the Diesel pump on 1998 and newer VW models equipped with a T.D.I. engine. This two piece lock plate and alignment pin allows the technician for factory correct and trouble free installations.

Tools on the right side of image are Diesel Lock Plate / Cam Setting Bar Same as Volkswagen ref 2065a Tool used for securing the cam shaft from rotating and maintaining correct timing position engine AAZ during R&R of cam shaft drive belt. Applicable: VW/Audi diesel and Volvo 6 cylinder 2.4L diesel 1981 86 Lock Pin for Diesel (Same as VW tool 2064). Tool used for securing Bosch diesel injection pump sprocket from rotating during R&R of cam shaft drive belt. This Locking Pin also assists in locating the general timing position of pump. Volkswagen Audi diesel and Volvo 6 cylinder 2.4L diesel 1981 86 All 4 tools are High Quality Made in Europe!

Relief Valve Tool 30.50
P236 Pressure Relief Valve Extractor Extractor the proper extraction of the from engine case. All Porsche VW Boxer 4
read more:

Engine Holding Fixture 339.00

Engine Holder P201 Designed to securely bolt up to every Porscheand VW air cooled engine ever produced.Please note: This item is included in the complete kit also.

Timing Belt Tensioner 44.95

Volvo Timing Belt Tensioner Tool with 6mm Hex Adjuster.On the 1998 and later Volvo engines the timing belt tensioner is located down near the bottom of the engine in a hard to reach area. This uniquely designed tool reaches down and rotates the 6mm hex adjuster on the timing belt tensioner so that one technician can easily set the correct tension preload and tighten the lockdown bolt. This unique tool works on all engines 98 and later with the 6mm allen adjuster and includes: 4 Cylinder, 1.9L, 5 Cylinder, 2.3L, 2.4L, 2.5L, 6 Cylinder, 2.8L, 2.9L

T.D.C. Tool 0.00
Top Dead Center Tool
Number 2588 1 Belt Changing Tool.
Should be used with 2588 2 and 2588 3. Call for more info.
High Quality Tool Made in Germany.
read more:

Engine Lifting Bracket 14.50

Engine Lifting Bracket
Fits most 2 and 4 barrel intakes Lifts engine by intake manifold 1,000 lb. maximum load

Crankshaft Gear Puller Volkswagen 86.50

Crankshaft Gear Puller for Volkswagen This inexpensive tool solves the problem of removing the crankshaft timing gear, a gear which must be removed when an engine is rebuilt and the main bearings are changed. In operation, this tool simply slips under the gear and with a twist of a wrench the gear is easily removed. The highest quality standards are used in the construction of this tool for years of repair shop service. To prevent damage to the end of the crankshaft, a ball bearing swivel is used, while for strength, the griping shoe is made of forged steel. For use on all type I, II, & III engines 40hp and later.

Flywheel Lock 22.95
215 Volkswagen Porsche Tool
Flywheel Lockused to secure the crankshaft from rotating during R&R of motor.
Used in conjunction with Engine Holding Fixture P201,
where Flywheel Lock bolts into a machined channel.
All Porsche and VW 6V or 12V, air cooled.Please note: This item is included in the complete kit also.
read more:

12 Pack Air Tool Oil 19.99
12 Pack Air Tool Oil.
Specially Formulated for use in all piston type and rotary air tools, as well as in line air lubricators. Prevents rust formation while providing positive lubrication for smooth starting and longer tool life. Assures maximum performance by dissolving gum and sludge that cut down tool speed and reduce power output. ( Marvel 12 Pack)
read more:

Transverse Bar 139.99
Engine Transverse Bar With Support Arm.
Features & Benefits: Makes removal of transaxle easy by supporting engine of front wheel drive vehicles. Support Arm provides three point support off center loads. Includes: 1/8' braded steel cables and 14' adjustable hooks. Capacity: 700 lbs.
read more:

Lisle Spark Indicator 7.99
Spark Indicator Tests Spark Plugs, Spark Plug Wires and Coils Without Puncturing the Wire.
With the engine running, place the grooved end of the tool over the plug wire.
The bulb will flash to indicate spark.
read more:

Deck Height Kit 29.95

This Tool measures the distance from the top of the cylinder to the top of the piston.
Proper deck height is essential in preventing the piston from hitting the cylinder head,
blue printing an engine and in calculating the compression ratio.
This easy to use tool measures deck height
with the use of its own calibrated, threaded screw or feeler guages,
dial indicators & calipers. It has been designed to allow the cylinder to be torqued
against the case for accurate measurement.
For use on type I, II, & III engines.

Press tool 401 0.00
High Quality German Made
Volkswagen Press Tool for assembly work.
Original Factory Tool.
read more:

Volkswagen Door Tool 9.99

T10011Volkswagen Door Tool triple Square 4
This is the correct tool for the job
New Beetle Tool This tool is used for R & R of door handle screws.Applicable: 1998 & newer VW Golf, Jetta, Passat & New Beetle....possibly other VW Audi.
This tool is a high quality item you will like.

Engine Lifting Chain 8.99
Engine Lifting Chain.
1,000 Maximum Load.
Link locking for balance and slip free lifting.
Heavy duty 24 inch chain.
(28 inch overall length).
Heat treated alloy steel.
read more:

944 Tool Set 60.50

Set of two tools for 944
Flywheel Lock needed to stop the motor from rotating during removal and replacement of crankshaft bolt or motor. Applicable: Porsche 944.

Alignment Pin ZDMAK number P218 Same as Porsche Tool 9215.
Alignment Pin crucial in order to properly reinstall the oil filter/water intercooler housing.
Not using this Alignment Pin may cause misalignment during this procedure, which may lead to the oil pressure relief valve sticking and ultimately engine damage.
Applicable: Porsche model 944 from 1983 to 1986.

BMW Harmonic Balancer Kit 295.00

This special service master kit was developed to make the difficult task of breaking loose the harmonic balancer / crank shaft bolt EASY by using tool numbers BMW 3050 1 in conjunction with BMW 3050 2.
Once the crank bolt is removed, the second phase of this kit is used for the critical task of extracting the sometimes stuck vibration damper by using tool numbers BMW 3050 2 in conjunction with BMW 3050 3
Applicable: BMW Engine M52TU, M54, M56.

Each item is also sold individually search for:
BMW30501
BMW30502
BMW30503

You Searched for

bmw engine tool

Trade Links With ZDMAK