honda tool FIND honda tool toyota service tools -- mmk4mkt

Honda Pulley Holding Tool 59.50

This tool is used for removal and installation of the crank bolt on most Honda and Acura engines. In operation with the use of a 1/2" breaker bar or ratchet this tool holds the harmonic damper pulley from rotating when removing the pulley bolt. There is a hole in the center of the tool to allow the use of a socket and extension to break loose or tighten the pulley bolt.Applications Accord 2.2L 4 cylinder 90 97; 2.7L 6 cylinder 96 97; 2.3L 4 cylinder 98 & later; 3.0L V 6 98 & later. Civic 1.6L 4 cylinder 92 & later. CRV 2.0L 4 cylinder 97 & later. Del Sol 1.6L 4 cylinder 93 97. Insight 1.0L 3 cylinder all. Odyssey 2.2L 4 cylinder 95 97; 2.3L 4 cylinder 98; 3.5L V 6 99 & later. Prelude 2.2L 4 cylinder 92 & later; 2.3L 4 cylinder 92 96 S2000 2.0L 4 cylinder all. ACURA CL 2.2L 4 cylinder 97; 3.0L V 6 97 & later; 2.3L 4 cylinder 98 & later. Integra 1.6L 4 cylinder 90 92 1.7L 4 cylinder 93 & later 1.8L 4 cylinder 94 & later. Legend 3.2L V 6 91 95. NSX 3.0L V 6 91 & later 3.2L V 6 98 & later. RL 3.5L V 6 96 & later. TL 3.2L V 6 95 & later.

Honda Dust Seal Tool Driver 14.00

For the proper installation of the dust seal onto the front knuckle.Applicable: Most early Honda model.

Honda Tool 39.99

Honda & Acura Harmonic Damper Pulley Puller Holder Tool made to properly secure the pulley from rotating during R & R of crank bolt.To break loose the crank shaft pulley / harmonic balancer bolt.The 50mm hex head armature slips past the tightest of spaces and slides properly into the center slot on the pulley. Slide the long bar onto the receiving end of the armature and lock it into position with the securing bolt!

Honda Acura Bushing Tool Kit 189.00

Honda Acura Bushing Removal and Installation Tool easily and quickly removes and install trailing arm bushing in 15 minutes per side versus the factory "book" time of 1.8 hours per side. No removing the arm from the vihicle and using a hydraulic press. No need to disconnect brake parts such as calipers, rotors, shoes, lines or brake cables.
Works on Civic 1988 2000, CRX 1988 1991, Del Sol 1993 1997
Acura Integra 1994 2001

AXLE WRENCH 0.00
MOTORCYCLE AXLE WRENCH19mm & 24mm sizes.This tool works on most Suzuki, Honda, Yamaha and Kawasaki motorcycles.This tool is used to install and remove front wheel axles and swing arm pivot shafts. It is a double sided wrench which has both a 19mm and 24mm hex. There is also a 3/8 inch square drive hole in the handle to provide easy torque adjustment.
read more:

Honda / Accura Counter Holder 79.50

HO50 applicable Honda and Acura models 1990 and Newer
with a 50mm hex slot in crank shaft pulley harmonic balancer.

Honda Toyota Nissan Tool 45.95

12mm Jam Nut Valve Adjustment Tool
Designed for a wide variety of cars with 12mm jam nut valve adjustment screws.
This two in one tool has a window in its socket so the technician can see the position of the screwdriver blade holding the
adjustment screw as the jam nut is tightened.
This visual contact in addition to the feel of holding the screwdriver The unique handle pivots from one side to the other, so the window is always visible.

Cam Shaft Seal Installer 49.95

Cam Shaft Seal Installer
HO100 Sub Kit
Applicable Honda engines 1.8L, 2.0L, 2.2L.All 4 cylinder Honda 1984 newer. Some 4 cylinder motorcycle engines.See Master Kit for more (number H0110)

Counter Holder Bonus Kit 145.00

Special kit for the professional Honda Acura Technicians2.5 foot long Securing bar. Used to properly counter the rotation of the crank shaft pulley harmonic balancerduring R&R of crank bolt. Honda and Acura models,90 and newer with a 50mm hex slot in crankshaft puller harmonic balancer.and Civic, 80 and newer.

Brake Caliper Rewind Set 47.99
U.S./EURO/ASIAN/4WD VEHICLES
Disc Brake Pad & Caliper Service Tool Kit
Includes 8 adapters Magnetic socket adapter.
For brake assemblies
For rotating pistons back into caliper to provide clearance for new pads
Prevents damage to the piston and bootDesigned for use with Mercedes, BMW, Volkswagen, GM, Audi, Ford,Honda, Subaru, Mazda, Nissan, Mitsubishi, Toyota, Land Rover and 4 wheel drive vehicles.Blow molded carryingcase for easy storage.
read more:

Tank Adapter 51.20

Spring Loaded Tank Adaptor
Needed for pressurizing the liquid cooling system.Applicable: Honda 1990 93 Accord, Honda Civic 1988 91.
TOYOTA 4 RUNNER 1996 and NEWERCAMRY V6 &AT ONLY 1990 91, CAMRY 92 93CAMRY WITH V6 1994, CELICA 1990 98 and NEWERCOROLLA 1993 and NEWER, ECHO 2000HIGHLANDER 2001 and NEWER, PASEO 1992 and NEWERRAV4 1996 and NEWER, SUPRA WITH TURBO 1990 92TERCEL 1991 99

Honda Acura Crank Seal Set 56.00

Honda / Acura Crank Seal Kit
This crankshaft oil seal installation kit was designed for proper and easy harmonic balancer oil seal installation. The press cup is high quality anodized aluminum which will not damage the oil seal or the engine. The threaded stepbolt screws into the crank bolt hole. The press nut and washer provides the technician with an even and straight pressing force, seating the new oil seal into the engine case with ease.

Honda Valve Adjustment 45.95

10mm Jam Nut Valve Adjustment Tool
Designed for a wide variety of cars with 10mm jam nut valve adjustment screws.
This two in one tool has a window in its socket so the technician can see the position of the screwdriver blade holding the
adjustment screw as the jam nut is tightened.
This visual contact in addition to the feel of holding the screwdriver The unique handle pivots from one side to the other, so the window is always visible.

Cam Shaft Seal Installer 81.95

This kit consists of "Two" Sub KitsThe numbers of the sub kits areHO 100 AND HO 105 pictured below.1.Cam Shaft Seal Installerand2.Balance Shaft Oil Seal KitHO100 Sub Kit Cam Shaft Seal Installer Applicable Honda engines 1.8L, 2.0L, 2.2L.All 4 cylinder Honda 1984 newer. Some 4 cylinder motorcycle engines.HO105 Balance Shaft Oil Seal Sub Kit Applicable on engines 2.0L and 2.2L, 90 and newer

Clamp Plier Tool 0.00

Hazet Clamp Pliers with lug holding down device,
special steel, nickel plated.
For axle collar clamps on passenger cars,e.g. on VW AUDI, OPEL, BMW, MERCEDES BENZ, HONDA, NISSAN, MAZDA.

Universal Cam Pulley Holder 55.00

Universal Cam Pulley Holder Comes in a plastic pouch with two sets of Pins. This tool isused on some Honda, Nissan, Mitsubishi, Toyota, Volvo Ford, Chrysler, Mercedes and BMW.

Oil Seal Installation Bonus Kit 159.50

Universal Asian Oil Seal Installation Bonus Kit
This special kit was designed for the proper installation of crank shaft oil seals, situated within confined areas on most 4, 6 and 8 cyl Toyota, Lexus, Nissan, Mitsubishi, Mazda and Infiniti.Application includes camshaft oil seal installation of Toyota Lexus 2.5L, 2.8L, 3.0L, 3.4L, 4.0L & 4.3L The stepbolts screw into the cam or crankshaft end. The press nut and washer allows for an even pressing force, seating the oil seal into the engine case with ease.

See tool TOY100 for 4 cylinder Asian camshaft oil seal installation. Honda Acura, see tool HO100, HO105, HO115, and HO115 WB.

Toyota / Asian Oil Seal Bonus Kit 159.50

5/8 (16mm) Spark Plug Wrench 73.99

Super High Quality
Spark Plug Wrench
With square drive size 3/8 inch (10mm).
Bonus feature is ball joint and fixing clamp inside for extra hold!
Tool for 16mm (5/8) spark plugs useful on a wide range of applications,
including motorcycles e.g.
KAWASAKI, YAMAHA, HONDA, SUZUKI, DUCATI etc...

T.D.C. Tool 0.00
Top Dead Center Tool
Number 2588 1 Belt Changing Tool.
Should be used with 2588 2 and 2588 3. Call for more info.
High Quality Tool Made in Germany.
read more:

Brake Caliper Rewind Set 49.50

U.S./EURO/ASIAN/4WD VEHICLES
Disc Brake Pad & Caliper Service Tool Kit
Includes 8 adapters Magnetic socket adapter.
For brake assemblies
For rotating pistons back into caliper to provide clearance for new pads
Prevents damage to the piston and bootDesigned for use with Mercedes, BMW, Volkswagen, GM, Audi, Ford,Honda, Subaru, Mazda, Nissan, Mitsubishi, Toyota, Land Rover and 4 wheel drive vehicles.Blow molded carryingcase for easy storage.

12 Pack Air Tool Oil 19.99
12 Pack Air Tool Oil.
Specially Formulated for use in all piston type and rotary air tools, as well as in line air lubricators. Prevents rust formation while providing positive lubrication for smooth starting and longer tool life. Assures maximum performance by dissolving gum and sludge that cut down tool speed and reduce power output. ( Marvel 12 Pack)
read more:

Press tool 401 0.00
High Quality German Made
Volkswagen Press Tool for assembly work.
Original Factory Tool.
read more:

Volkswagen Door Tool 9.99

T10011Volkswagen Door Tool triple Square 4
This is the correct tool for the job
New Beetle Tool This tool is used for R & R of door handle screws.Applicable: 1998 & newer VW Golf, Jetta, Passat & New Beetle....possibly other VW Audi.
This tool is a high quality item you will like.

End Play Kit 00
This tool has isdesigned to measure the end play movement
of the VW crankshaft without the use of a dial indicator.
All that is necessary is a feeler gauge set and this tool.
With the tool bolted to the end of the case, the feeler guage
measures the gap created by the end play.
The taking of this end measurement is necessary whenever a VW engine is rebuilt
to prevent the rear main bearing from seizing up.
A must for rebuilding one engine or many,
this tool works on all air cooled VW engines and Porsche 912 & 914 models.
read more:

BMW Radio Tool 15.00

Very popular BMW Radio Removal Tool.
Pentagon shaped tool with 5 Sides.
The overall length of this tool is 3 5/8 inches.
Applicable: Most BMWs.
Including E38 E39 7 Series etc...
This tool is used to release anti theft radio mounts.

7 Way Crimping Tool 8.99
7 WAY CRIMPING TOOL
Wire cutter, terminal crimper & wire stripper in one handy tool
Black anodized finish with insulated hand grips
Crimp slot on end of tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals
Crimps 7mm to 8.5mm ignition wire
Works with 10 22 gauge solderless terminals
read more:

Klein Tool Bag 94.50
Klein Tool Bag
Number 5002 20
20" Tool Bag, No. 8 natural canvas with vinyl 20" (51 cm) 6" (15 cm) 15" (38 cm)

Klein offers a full line of Tool Bags. With the addition of two 20" bags you can now carry more tools and products. The 5003 series has shoulder strap mounts for use with the new shoulder strap. The canvas tool line has tool bags in lengths of 16" (8 interior pockets), 18" (10 interior pockets) and the new 20" (14 interior pockets) with choices in either leather or vinyl bottoms. Now carry all of your tools the most convenient way for you!
read more:

Honda Acura B90 Only 381.00

Call or Email with any questions.

Klein Tool Bag 89.99
Klein Tool Bag
Number 5003 16
16" Tool Bag, No. 8 natural canvas with leather 16" (41 cm) 6" (15 cm) 14" (36 cm)

Klein offers a full line of Tool Bags. With the addition of two 20" bags you can now carry more tools and products. The 5003 series has shoulder strap mounts for use with the new shoulder strap. The canvas tool line has tool bags in lengths of 16" (8 interior pockets), 18" (10 interior pockets) and the new 20" (14 interior pockets) with choices in either leather or vinyl bottoms. Now carry all of your tools the most convenient way for you!
read more:

Spark Plug Boot Tool 32.99
Spark Plug Boot Tool
Due to restricted space the T10029 will install the spark plug boot properly.
VW and Audi spark plug boots designed to seal and increase contact between the spark plug and spark plug wire.
With the increased seal and location of the boot,
this tool has been made to access and remove the spark plug boot.
Tool is approximately 10 inches (250mm) long.
Used to pull off the spark plug socket...SOME APPLICATIONS INCLUDE: 2.8 2.9L VR6 engines
VW Golf, Corrado and Passat.Also Audi 80, 100, A4, A6 with 2.6 and 2.8L V6 engines.
This is the correct tool for the job.You will most likely find OLD number 3277 or 3277A in your manuals but
T10029 is the CORRECT current Volkswagen Audi Tool number. 3277 is and old number and Volkswagen calls this a SPARK PLUG CONNECTOR TOOL.
read more:

7 in 1 Tool 8.50
7 in 1 TOOL
Includes Wire looper, steel wire cutter,
copper wire cutter, wire stripper,
crimping tool, hose clamp plier and inch/metric scale!
read more:

Puller Extractor 17.50

Needed for the proper extraction of auxiliary valves.
Used in conjunction with a slide hammer. Applicable: Most every early Honda model.

Valve Spring Tool & Bridge 142.50

Valve Tools (2)
Set including:Valve Spring Compressor Bar
Same as Volkswagen Tool Number VW 541/1
Used for R&R of valve spring or rocker armWith this tool the job can be done with the cylinder head on or off the car.Used in conjunction with tool BridgeApplicable: 924 / 944 VW AUDI 4 5 Cyl. VA6022Support Bridge Same as VW Tool 2036 Used for R&R of valve spring or rocker armUsed in conjunction with tool VW541/1Applicable: Model 924. VW / AUDI 4 5 Cyl.

Valve Spring Tool and Bridge 142.50

Valve Spring Tools Set including:VA6010Valve Spring Compressor BarSame as Volkswagen Tool Number VW 541/1Used for R&R of valve spring or rocker armWith this tool the job can be done with the cylinder head on or off the car.Used in conjunction with tool BridgeApplicable: 924 / 944 VW AUDI 4 5 Cyl. VA6022Support Bridge Same as VW Tool 2036 Used for R&R of valve spring or rocker armUsed in conjunction with tool VW541/1Applicable: Model 924. VW / AUDI 4 5 Cyl.

12 Pack 32 oz Air Tool Oil 64.99
32 oz 12 Pack MVL085
Specially Formulated for use in all piston type and rotary air tools, as well as in line air lubricators. Prevents rust formation while providing positive lubrication for smooth starting and longer tool life. Assures maximum performance by dissolving gum and sludge that cut down tool speed and reduce power output. ( Marvel 12 Pack)
read more:

Arbor Installer Kit 39.50

Honda & Acura Oil Seal ArborNeeded for the proper installation of Balance Shaft Oil Seal.
Applicable: 4 Cyl 2.0L and 2.2L 1990 and Newer.

BMW Center Cap Tool 8.99

BMW Center Cap Tool.Made in Germany
Tool used to remove and install center caps on several BMW.
Drive size is 17mm
Tool is 3 7/16 inch wide.
BMW NUMBER 36 13 1 180 626

Stubby 3/8 X 1/2 Ratchet 23.99
Short Pattern Double Drive 3/8 X 1/2
Flexible Head "Stubby" Ratchet
Comfortable rubber cushion grip handle Features 72 gear teeth for speed & durability Chrome vanadium steel construction.
Saves space in the tool pouch or tool box,
saves time looking for a tool
and saves money!
read more:

3 pc. Fold Up Tool Set 45.99

3 pc. Fold Up Tool Set
3 fold up tools all made of high alloy CVM steel, hardened, with a molded ergonomic handle. 7 tool PocketStar: Torx sizes: T7, T8, T9, T10, T15, T20, T25. 7 tool MagicRing Metric PocketStar: 2, 2.5, 3, 4, 5, 6 and 8mm. 9 tool MagicRing Inch PocketStar: sizes 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32, 1/4 in
Satisfaction Guaranteed Made In Germany!

VW803 19.99
Sorry No Picture
FACTORY TOOL
In Stock Now!
Call if you need more info on this tool.
read more:

VW276 49.99

Sorry No Picture

FACTORY TOOL MADE IN GERMANY

In Stock Now!
Call if you need more info on this tool.
read more:

VW243 39.99

Sorry No Picture

FACTORY TOOL MADE IN GERMANY

In Stock Now!
Call if you need more info on this tool.
read more:

VW244B 125.00

Sorry No Picture

FACTORY TOOL MADE IN GERMANY

In Stock Now!
Call if you need more info on this tool.
read more:

VW801 49.99

Sorry No Picture

FACTORY TOOL MADE IN GERMANY

In Stock Now!
Call if you need more info on this tool.
read more:

Power Lifter Pickup Tool 18.50
Pick up Tool 19 inch long with lift cap 1.5lbs.
read more:

VW273A 125.00

Sorry No Picture

FACTORY TOOL MADE IN GERMANY

In Stock Now!
Call if you need more info on this tool.
read more:

Super Duty Disc Brake Tool 0.00
Heavy Duty Brake Tool
For safe resetting of disc brake pistons
on vehicles with fixed caliper disc brakes.
Extremely High Quality Tool Made in Germany.
Call for more info.
read more:

Long Pattern Hex Set 4 13.50

4 Pc Long Allen Hex Set
Sizes include: 6, 7, 8, and 10mm Hex.
This set works well on several vehicles such as Audi, AMC, BMW,
Honda, Jaguar, Jeep, Saab, Volkswagen and Volvo.
3/8 Drive set of 4

Trunk Tool Kit Plier 28.50

Waterpump Plier for Trunk Tool Kit
Brand New Factory Tool
Made in Germany by Heyco
Stamped Heyco BMW on raised panel.
The overal length of this tool is 7 3/4 inch at smallest setting (the length when fully open is 8 7/16.
The tray opening will be close to 7 3/4.
Replace your missing Pliers with this Factory original Tool!
BMW NUMBER 71 11 1 179 522

You Searched for

honda tool

Trade Links With ZDMAK