passat tool tdi tool bmw special tools tdi diesel -- mmk4mkt

Volkswagen Door Tool 9.99

T10011Volkswagen Door Tool triple Square 4
This is the correct tool for the job
New Beetle Tool This tool is used for R & R of door handle screws.Applicable: 1998 & newer VW Golf, Jetta, Passat & New Beetle....possibly other VW Audi.
This tool is a high quality item you will like.

Passat Seal Tool 19.50

T10249 Made in Germany
Used for sealing lines when removing additive reservoir.Passat 4 cyl. diesel engine (2.0 ltr. engine)

Brake Caliper Tool 110.00

T10165 Brake Caliper Tool
The old number for this tool was 3272
(discontinued)
T10165 is the correct current factory number for this tool.
Brand New Tool
Made in Germany.
Some Vehicles include: Beetle 1.8 Turbo
(see your manual for exact year model applications tool number T10165 or old number 3272 same as T10165)
Beetle 4 CYL , Beetle TDI Diesel , Corrado SLC V6 ,
Golf Cabrio IV GL , Golf Cabrio IV GLX , Golf III GL 4 CYL ,
Golf III GTI 4 CYL , Golf III GTI VR6 , Golf III TDI Diesel , Golf IV 4 CYL ,
Golf IV GL 4 CYL , Golf IV GLS 4 CYL, Golf IV GTI 1.8 Turbo ,
Golf IV GTI VR6 AFP , Golf IV TDI Diesel , Golf IV VR6 AFP ,
Jetta III GL 4 CYL , Jetta III GLS 4 CYL , Jetta III GLX VR6 ,
Jetta III TDI Diesel , Jetta IV 1.8 Turbo , Jetta IV GL 4 CYL ,
Jetta IV GLS 4 CYL , Jetta IV GLS VR6 AFP , Jetta IV GLX VR6 AFP,
Jetta IV TDI Diesel , Jetta Wagon 1.8 Turbo , Jetta Wagon 1.9 TDI ALH ,
Jetta Wagon 4 CYL AZG / AVH, Passat TDI Diesel ,
Passat V6 30V AHA / ATQ , PassatTurbo 20V AEB

Spark Plug Boot Tool 32.99
Spark Plug Boot Tool
Due to restricted space the T10029 will install the spark plug boot properly.
VW and Audi spark plug boots designed to seal and increase contact between the spark plug and spark plug wire.
With the increased seal and location of the boot,
this tool has been made to access and remove the spark plug boot.
Tool is approximately 10 inches (250mm) long.
Used to pull off the spark plug socket...SOME APPLICATIONS INCLUDE: 2.8 2.9L VR6 engines
VW Golf, Corrado and Passat.Also Audi 80, 100, A4, A6 with 2.6 and 2.8L V6 engines.
This is the correct tool for the job.You will most likely find OLD number 3277 or 3277A in your manuals but
T10029 is the CORRECT current Volkswagen Audi Tool number. 3277 is and old number and Volkswagen calls this a SPARK PLUG CONNECTOR TOOL.
read more:

Tappet Depressor Set 81.50

VW546 Tappet Depressor Tappet Depressor used for preloading cam followers. For Bucket Tappets on VW Golf, Jetta, Caddy, Scirocco, Passat up to 1982 Also Audi 80 , 100

Plus 2078A Tappet Depressor needed for preloading cam followers while exchanging valve adjusting shims. Applicable: Late model VW Audi 4 and 5 cylinder gas engines. More Detail: Some German Tool books have the following info on this tool... For all 4 cylinder engines with bucket tappets 1983 and Newer and all 5 and 6 Cylinder with bucket tappets Golf, Jetta, Scirocco, Passat, Audi 80, Audi 80 Coupe, Audi 80 Quatro, Audi 100, 200, LT28 50D.

Hazet Tensioning Tool 75.98

Driving Tool for Tensioning Device
special steel, for operating devicewhen changing the V ribbed belt,especially on VW Polo, Golf and Passat, AUDI since 1991.

Triple Square Drain Plug Tool 49.50

This is a Special Tamperproof * Transmission Drain Plug Socket. Triple Square ( 12 Point XZN 16) Same as old Volkswagen Tool 3357. (Number 3357 is still found in many/most manuals for this job)
Applicable Porsche Boxster and Audi A4 A6 and Passat. This is an excellent high quality tool Made in Germany. Plug not included, picture is for reference only.

Spark Plug Boot Tool 24.99

Spark Plug Boot Tool
Due to restricted space the T10029 will install the spark plug boot properly.
VW and Audi spark plug boots designed to seal and increase contact between the spark plug and spark plug wire.
With the increased seal and location of the boot,
this tool has been made to access and remove the spark plug boot.
Tool is approximately 10 inches (250mm) long.
Used to pull off the spark plug socket on 2.8 2.9L VR6 engines
VW Golf, Corrado and Passat.Also Audi 80, 100, A4, A6 with 2.6 and 2.8L V6 engines.
This is the correct tool for the job.You will most likely find OLD number 3277 or 3277A in your manuals but
T10029 is the CORRECT current Volkswagen Audi Tool number. 3277 is and old number and Volkswagen calls this a SPARK PLUG CONNECTOR TOOL.

PULLEY HOLDING TOOL 74.99

AUDI & VW
FAN CLUTCH PULLEY HOLDING TOOL
AUDI 1996 2001 A6 2.8L V 6 & VW 1998 & later Passat 3.0L V 6

Shock Tool Drive Nut 26.50

Shock Tool Drive Nut
See image with details above
Please notice this is item 2593 2(A)
Pin size 3.5mm with inner (span) size 10.5mm.
More data below on the tool.
Chassis Shock Absorber 2593 Hex Head Wrench
For front axle Golf II, III,
Jetta, Vento, Passat from model 88,
AUDI 80 from 87.
If you are notsure about your size please call or email first.
No return on this item unless defective.

Drainplug Tool on Sale! 14.99

Drain Plug Socket
This is a Special Tamperproof Transmission Drain Plug Socket.
Triple Square ( 12 Point XZN )
Same as Volkswagen Tool 3357.
For Porsche Boxster and Audi A4, A6 and Passat.

Best Quality XZN Size M16 49.50

This is a Special Tamperproof Transmission Drain Plug Socket. Triple Square ( 12 Point XZN 16) Same as old Volkswagen Tool 3357. (Number 3357 is still found in many/most manuals for this job)
Applicable Porsche Boxster and Audi A4 A6 and Passat. This is an excellent high quality tool Made in Germany.
* Plug not included, picture is for reference only.

Tri Square Drain Plug XZN 49.50

Headbolt & Drain Plug Socket Set 2 28.00

Drain Plug Socket
Plus Heabolt Tool
Details: Tamperproof Transmission Drain Plug Socket.
Triple Square (12 Point XZN)
Same as Volkswagen Tool 3357.
For Porsche Boxster and Audi A4, A6 and Passat.

Plus Audi Headbolt Tool
Number T10070 Headbolt Tool 1/2 Drive Used to remove and install cylinder headbolts. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2 inch. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. Set of 2 Audi Tools from ZDMAK

Dont hesitate...these are BOTH the CORRECT tools for the job!

Tappett Depressor 44.99

Tappet Depressor needed for preloading cam followerswhile exchanging valve adjusting shims.Applicable: Late model VW Audi 4 and 5 cylinder gas engines.More Detail: Some German Tool books have the following info on this tool...For all 4 cylinder engines with bucket tappets 1983 and Newerand all 5 and 6 Cylinder with bucket tappetsGolf, Jetta, Scirocco, Passat, Audi 80, Audi 80 Coupe,Audi 80 Quatro, Audi 100, 200,LT28 50D

Tappet Depressor 44.99

Tappet Depressor 2078A used for preloading cam followerswhile exchanging valve adjusting shims.Applicable: Late model VW Audi 4 and 5 cylinder gas engines.More Detail: Some German Tool books have the following info on this tool...For all 4 cylinder engines with bucket tappets FROM YEAR 1983 and Newerand all 5 and 6 Cylinder with bucket tappetsGolf, Jetta, Scirocco, Passat, Audi 80, Audi 80 Coupe,Audi 80 Quatro, Audi 100, 200, LT28 50D

Headbolt & Drain Plug Socket Set 28.00

TWO TOOLS!!!
Audi Headbolt Tool (LEFT)Number T10070 Headbolt Tool 1/2 Drive Used to remove and install cylinder headbolts. Volkswagen Audi V6 and 4 Cylinder 5 valve engines. Long pattern for deep located screws. Drive size is 1/2 inch. Many Audi Headbolts have switched to the new pattern. This will fit into the new special screw profile. Plus Drain Plug Socket (right)Special Tamperproof Transmission Drain Plug Socket.Triple Square (12 Point XZN)Same as Volkswagen Tool 3357.For Porsche Boxster and Audi A4, A6 and Passat. Dont hesitate...these are BOTH the CORRECT tools for the job!

Bar and Pin for 5 Valve 139.50

Camshaft Timing Tool Set (2)
TOOL REF 3391
Cam/Bar Holder
V6 / 5 valves per cylinder/
used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during timing belt change /head assembly work.
Applicable VW Audi V6 5 Valve 1998 2003
Cam/Bar Holder Not Applicable 3.0 2002 4 cam.

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6Please note: 3391 for 5 valves per cylinder.

Hazet Quality Tools 75.98

Driving Tool for Tensioning Device
special steel, for operating devicewhen changing the V ribbed belt,especially on VW Polo, Golf and Passat, AUDI since 1991.

Transport Brackets 59.10

Engine Brackets Original Factory Tool Made in Germany: USED WHEN REMOVING AND INSTALLING W8 ENGINE ON PASSAT.

Chain Adjuster 24.50

3366CHAIN ADJUSTER Required to change the troublesome cam adjuster seal
Audi and Volkswagen 4, 6 (2.7 and 2.8) and 8 CylWith 5 Valve per Cyl.
Also Audi VW 1.8 Golf Jetta Passat New Beetle
Note:The manual says to remove both camshafts to change the seal ...
but using this tool you can relieve the tension on the camshaft chainand lift it up far enough to clean, remove and replace the gasket and seal.
This procedure not only saves time but saves any other damagethat may happen to camshafts and bearings by removing them.
ORIGINAL MATRA FACTORY TOOL MADE IN GERMANY

Airbag Tool 15.50

USED FOR RELEASING AIR BAG MODULE ON 3 SPOKE LEATHER STEERING WHEEL IN PASSAT W8. ALSO 3 SPOKE STEERNG WHEEL IN GOLF AND JETTA WITH WOODEN SURROUND. MADE IN GERMANY

Big Mak 126.00
Master Kit
Set of 6 Tools
Including Dial Indicator

Set Includes:
3032 Injection Pump Tool Puller used for the proper extraction of injection pump drive gear. Applicable: Volvo and VW / Audi diesels Excluding TDI
PLUS: VA6015 Holder used for accurate adjustment of Bosch diesel injection pump.
Plus: 2065A Diesel Camshaft Locking Plate Tool
PLUS: 2064 Lock Pin for Diesel.
Plus the Pin Wrench (made in Germany) for easy adjustment of Camshaft spur belts (toothed belt) on idler Pulleys with Pin holes. This wrench with its protruding pins, grabs the center of the idler pulley and rotates around the off center retaining bolt allowing for easy belt tension adjustment. Tension Pulleys on 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80.
Plus Dial Indicator
read more:

Threaded Pin for T.D.C. 25.00

Locking Pin
TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF
BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6
For installing or removing toothed belt /flywheel drive plate.

Cam Bar and Pin for 2 Valve 139.50

Camshaft TimingTool Set (2)
TOOL REF 3243
Cam/Bar Holder 2 valves per cylinder/
Used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during belt change head assembly work.
Applicable Audi 90 A6 A4  94 97 AFC Engine

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF
BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6

Please note: 3243 for 2 valves per cylinder. 

Cam Bar and Pin for 2 Valve 139.50

Spark Plug Socket Remover 59.50

Spark Plug Socket Remover for INSTALLING and REMOVING normal or hot engines. Tool has a slotted cable for careful guidance of the cable..
For VR6, Golf, Passat, Corrado, Audi 80, 100, A4, A6 with 2.4 and 2.8I V6.

Pin Wrench Set 2 49.00

This is the Best Quality Set of the two CRUCIAL VW Audi Pin Wrenches you will find anywhere.
SUPER HIGH QUALITY TOOLS (BOTH) MADE IN GERMANY BY HAZET.
First item is number V159 (this is a smaller tool on the left side picture is not to scale) This tool is for easy adjustment of Camshaft spur belts
(toothed belt) on idler pulleys with Pin holes. This wrench with its protruding pins, grabs the center
of the idler pulley and rotates around the off center retaining bolt allowing for easy belt tension adjustment.
Tension Pulleys on 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80
Distance of pins 18 mm, diameter of pins 2.9 mm for deep located idler pulley
on toothed belt on 1,6 l diesel engine VW van T3 (up to model 1991).
V159 is the correct number the old VW Number on this (smaller) tool was 2587.

T10020 Special wrench with an offset (angled) head (Larger tool on right side of image)
This tool also used for adjusting timing belt tension.
99 and later VW Golf, VW Jetta and Beetle with 2.0 Litre Gas and 1.9 Litre TDI Engines.1999 and newer Golf, Jetta
New Beetle with 2.0l gas engine and 1.9l T.D.I. Diesel engine. You will get both tools with this purchase.

Set 2 Alternator Tools 47.00

Combo Socket Set of 2 consisting of the 17mm Multi Spline Adapter and XZN (12 Point) Socket size M10 for mounting and dismounting the alternator pulley at the generator.Volkswagen Audi Mercedes Porsche etc...For mounting the V belt pulley (slip clutch pulley) at the alternator (manuals call it a generator), especially for T.D.I. VW Golf III, Vento, Passat and AUDI A 3 .
The short serrated socket (3400) is size 17MM outside diameter and Length is 30mm.
The larger tool is M10 XZN triple square and is 1/2 drive x 140mm Length.Also for Boxster. (See repair Group 27 (Porsche Bulletins) Boxster Alternators with free wheeling Pulleys. High Quality Tool

Also: 1990 to 1994 porsche C2 and C4 and all porsche 993s use a (M10) 10mm 12point socket tool to hold the alternator shaft when replacing the belts the area between the alternator and car body is very limited a 10mm 12point spanner style wrench works well for this job.

Factory Tool 3417 29.50

Item Number 3417 Original Oil service Wrench 74mm with14 Points (inside flats flutes).
Applications include: Audi, VW Golf, and new body Jetta, TDI (Diesel)
and the following gas vehicles; Passat, Golf and Jetta with 1.8 turbo and 2.0litre,
Rabbit, Dasher, Scirocco, and New Beetle.
Super High Quality Original Factory Tool Made in Germany!
Clickhere to see a detailed Application ChartMeasure filter diameter canister diameter or Check yourmanuals for details and size needed.

T.D.C. Tool 0.00
Top Dead Center Tool
Number 2588 1 Belt Changing Tool.
Should be used with 2588 2 and 2588 3. Call for more info.
High Quality Tool Made in Germany.
read more:

Triple Square Socket 3357 14.99

Drain Plug Socket
This is a Special Tamperproof Transmission Drain Plug Socket.
Triple Square ( 12 Point XZN )
Same as Volkswagen Tool 3357.
For Porsche Boxster and Audi A4, A6 and Passat.

Triple Square Socket for Transmission 28.50

Drain Plug Socket:This is a Special Tamperproof * Transmission Drain Plug Socket.Triple Square ( 12 Point XZN ) Same as Volkswagen Tool 3357.For Porsche Boxster and Audi A4 A6 and Passat.This is an excellent "Stronger One Piece" design.

Radio Kets Set 13.99
3316 Radio Removal Tools New Body Style Passat Jetta GolfPlease check your manuals for details.
read more:

Radio Removal Set 24.99

Set of Volkswagen Audi Radio Removal Tools Audi A4, A6, A8 and New Beetle For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box.
PLUS * Set Number vw 3316 Radio Removal Tools New Body Style Passat Jetta Golf Please check your manuals for details.
You will get virtually full VOLKSWAGEN coverage with this set
Plus BMW Radio Removal Tool.Pentagon shaped tool with 3 5/8 inches overall length.Applicable: Most BMWs.This Five sided driver is used to release anti theft radio mounts.YOU ALSO GET THE SPECIAL SMALL ALLEN (Right) side of picture FOR NEWER E38 & E39 7 SERIES
Plus * MERCEDES RADIO REMOVAL KEYS FOR NEWER AND OLDER VEHICLES

Alternator Socket 27.00

For mounting the V belt pulley (slip clutch pulley) at the alternator (manuals call it a generator),
especially for T.D.I. VW Golf III, Vento, Passat and AUDI A 3
17MM outside dia. Length 30mm.
Also for Boxster. (See repair Group 27 (Porsche Bulletins) Boxster Alternators with free wheeling Pulleys. High Quality Tool
Made in Germany.
This 3400 is Hazet number 2592.

Hazet Oil Service Tool 29.50

Oil service Wrench 74mm with 14 Points (inside flats flutes).
Some applications include: Mercedes, Audi, VW Golf,
and new body Jetta, TDI (Diesel) and the following gas vehicles;
Passat, Golf and Jetta with 1.8 turbo and 2.0 litre, Rabbit, Dasher, Scirocco,and New Beetle.
Mercedes M104, M110, M111, M119, M120 C, E
Porsche 944 and 924. 
Some Toyota (Filter 08922 0211 etc...)
Can also be used on BMW Top of housing 1.9L M44
Super High Quality Original Factory Tool Made in Germany!
Clickhere to see a detailed Application ChartMeasure filter diameter canister diameter or Check yourmanuals for details and size needed.

Complete VW Audi Radio Keys 24.99

VW Audi Set Valve Tools 49.99

Two (2) Valve Adjusting Tools
Valve Shim Tool (10 208) Used for proper R&R of valve adjusting shims.
Applicable: Overhead Cam engines with adjusting shims
Plus
VW546 Tappet Depressor Tappet Depressor used for preloading cam followers.
For Bucket Tappets on VW Golf, Jetta, Caddy, Scirocco,
Passat up to 1982 Also Audi 80 , 100

12 Pack Air Tool Oil 19.99
12 Pack Air Tool Oil.
Specially Formulated for use in all piston type and rotary air tools, as well as in line air lubricators. Prevents rust formation while providing positive lubrication for smooth starting and longer tool life. Assures maximum performance by dissolving gum and sludge that cut down tool speed and reduce power output. ( Marvel 12 Pack)
read more:

BigMak Timing Kit 196.00

Master Kit
Set of 6 Tools
Including Dial Indicator

Set Includes:
3032 Injection Pump Tool Puller used for the proper extraction of injection pump drive gear. Applicable: Volvo and VW / Audi diesels Excluding TDI
PLUS: VA6015 Holder used for accurate adjustment of Bosch diesel injection pump.
Plus: 2065A Diesel Camshaft Locking Plate Tool
PLUS: 2064 Lock Pin for Diesel.
Plus the Pin Wrench (made in Germany) for easy adjustment of Camshaft spur belts (toothed belt) on idler Pulleys with Pin holes. This wrench with its protruding pins, grabs the center of the idler pulley and rotates around the off center retaining bolt allowing for easy belt tension adjustment. Tension Pulleys on 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80.
Plus Dial Indicator

COOLING TOOL 47.50

Expansion Tank Adapter Anodized AluminumTank Adaptor used for pressurizing the liquid cooling system. Applicable: VW Corrado, Quantum, Jetta 1990 and newer, Golf 1990 newer,Eurovan 1993 up, Passat with VR/6 1993 and newer.
Check out the (Adobe)
Cooling Adapter Application Charts Here

Puller, Pin , Plate , Holder , Pin Wrench 146.00

Set of five tools: vw 3032, VA6015 PLUS 2065A PLUS 2064 PLUS 12717
Details:
3032 Injection Pump Tool Puller used for the proper extraction of injection pump drive gear. Applicable: Volvo and VW / Audi diesels Excluding TDI * PLUS: VA6015 Used for accurate adjustment of Bosch diesel injection pump. PLUS: 2065A Diesel Camshaft Locking Plate Tool PLUS: 2064 Lock Pin for Diesel. Plus the Pin Wrench (made in Germany) for easy adjustment of Camshaft spur belts (toothed belt) on idler Pulleys with Pin holes. This wrench with its protruding pins, grabs the center of the idler pulley and rotates around the off center retaining bolt allowing for easy belt tension adjustment. Tension Pulleys on 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80.

Press tool 401 0.00
High Quality German Made
Volkswagen Press Tool for assembly work.
Original Factory Tool.
read more:

End Play Kit 00
This tool has isdesigned to measure the end play movement
of the VW crankshaft without the use of a dial indicator.
All that is necessary is a feeler gauge set and this tool.
With the tool bolted to the end of the case, the feeler guage
measures the gap created by the end play.
The taking of this end measurement is necessary whenever a VW engine is rebuilt
to prevent the rear main bearing from seizing up.
A must for rebuilding one engine or many,
this tool works on all air cooled VW engines and Porsche 912 & 914 models.
read more:

Best Seller ! Radio Tools Set 24.99

This is one of the best sets on the market. This is a Master Set for BMW Mercedes Porsche VW Audi and DIN. Included is a total of 3 different sets Volkswagen Audi, two different tools for BMWand a set for Mercedes Porsche and a DIN Ford set. The VW Tools (4) Number T10057Audi A4, A6, A8 and New Beetle For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box. If you have 4 slots VW AUDI this is the 4 keys you need) Plus you get Number VW 3316 (2) Radio Removal Tools New Body Style Passat Jetta Golf . You will get virtually full coverage forVolkswagen Audi when you buy this master set. The BMW Radio Removal Tools areone Pentagon shaped tool with a 3 5/8 inches overall length. Applicable: Most BMWs. This Five sided driver is used to release anti theft radio mounts.You will also get the special rare small allen tool for BMW (upper left) Fornewer BMW E38 & E39 7 SERIES Plus Mercedes most coverage for newer and oldervehicles, especially 1992 and newer 129, 140, 163, 202 & 210 PLUS Range Rover with Becker Nav System.The MB Tools also work on Porsche. Appl: Turbo GT, GT2, GT3, Boxster, Cayenne 911, 996 , 987, Carrera etc. Same as Porsche ref: 000 721 957 01

BMW Radio Tool 15.00

Very popular BMW Radio Removal Tool.
Pentagon shaped tool with 5 Sides.
The overall length of this tool is 3 5/8 inches.
Applicable: Most BMWs.
Including E38 E39 7 Series etc...
This tool is used to release anti theft radio mounts.

7 Way Crimping Tool 8.99
7 WAY CRIMPING TOOL
Wire cutter, terminal crimper & wire stripper in one handy tool
Black anodized finish with insulated hand grips
Crimp slot on end of tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals
Crimps 7mm to 8.5mm ignition wire
Works with 10 22 gauge solderless terminals
read more:

ANTI THEFT RADIO KEY SET 35.99
"NEW"
O.E. ANTI THEFT
RADIO KEY SWITCH BLADE STYLE
Radio Removal Kit Features:
Special features:. Each key folds into the body
handle like a pocket knife.
. Each half of the tool kit allows for an even pulling action.
. The two halves slide and are held together
via an interlocking channel.
. Every Key in the kit is current up to 2005.
The full application range of this new kit is as follows:
. Updated application key kit for Mercedes & all Porsche 996
and Boxster equipped withBecker radios.
. Updated key combo for all Audi & VW radios up to 2004:
models equipped with fourhorizontal (Audi) or two vertical slots (New Beetle, Jetta, etc.).
. VW only key kit for Passat, Jetta, Golf models. This key application range ends wherekey kit 2 begins.
. Five sided "pentagon" driver for most every BMW model, excluding E38 & E39 models.
. Special Allen key for BMW E38 and E 39 models.
. Standard "barbed hooks" (like U Hooks) for Ford, Chevy, Saab, Land Rover, etc.
read more:

Switch Blade Radio Keys 37.50
O.E. ANTI THEFT RADIO KEY SWITCH BLADE
Radio Removal Kit Features:Special features:. Each key folds into the body handle like a pocket knife.. Each half of the tool kit allows for an even pulling action.. The two halves slide and are held together via an interlocking channel.. Every Key in the kit is current up to 2005.The full application range of this new kit is as follows:. Updated application key kit for Mercedes & all Porsche 996 and Boxster equipped withBecker radios.. Updated key combo for all Audi & VW radios up to 2004: models equipped with fourhorizontal (Audi) or two vertical slots (New Beetle, Jetta, etc.).. VW only key kit for Passat, Jetta, Golf models. This key application range ends wherekey kit 2 begins.. Five sided "pentagon" driver for most every BMW model, excluding E38 & E39 models.. Special Allen key for BMW E38 and E 39 models.. Standard "barbed hooks" (like U Hooks) for Ford, Chevy, Saab, Land Rover, etc.
read more:

You Searched for

passat tool

Trade Links With ZDMAK